The P0717 Input Turbine Speed Sensor is located on the turbine shaft, just behind the turbine blades. This sensor monitors the speed of the turbine and sends a signal to the engine control module (ECM). If the turbine speed falls below a certain level, the ECM will activate the engine’s fail-safe mode and shut down the engine.
The P0717 code is triggered when the input turbine speed sensor (TSS) is not sending the correct signal to the powertrain control module (PCM). This can be caused by a number of different issues, but most often it is due to a problem with the TSS itself. The TSS is located on the transmission, and its function is to send a signal to the PCM that indicates how fast the engine’s input shaft is spinning.
If this signal is inaccurate, it can cause all sorts of problems with shifting, engine timing, and fuel delivery.
Fortunately, diagnosing and repairing a P0717 code is usually fairly straightforward. First, you’ll need to check for any obvious signs of damage or corrosion on the TSS.
If everything looks good there, then the next step is to test the output of the sensor using a multimeter. Once you have confirmed that the sensor itself is functioning properly, you can move on to checking for other potential causes like loose wiring or an electrical shorts.
How To Replace An Input Shaft Speed Sensor or Mainshaft Speed Sensor P0716 / P0717 / P0718
Where is the Turbine Speed Sensor Located?
The turbine speed sensor is located on the turbine shaft. It measures the rotational speed of the turbine and sends a signal to the controller. The controller uses this information to regulate the flow of gas to the turbine.
How Do I Fix Code P0717?
If you’re getting the P0717 code, it means that your vehicle’s transmission is slipping. This can be caused by a few different things, but the most common cause is low fluid levels.
Check your transmission fluid level first and top it off if necessary.
If that doesn’t fix the problem, then you may need to have your transmission serviced or replaced.
What Does the Turbine Shaft Speed Sensor Do?
The turbine shaft speed sensor is a vital component in a gas turbine engine. It measures the rotational speed of the turbine shaft and sends this information to the engine control unit. The engine control unit uses this data to regulate the fuel flow to the turbines, ensuring that they operate at peak efficiency.
Without a functioning turbine shaft speed sensor, an engine would be unable to maintain optimal performance and could eventually overheat and fail.
What is Another Name for the Input Shaft Speed Sensor?
An input shaft speed sensor is also known as a vehicle speed sensor. It is a device that measures the rotational speed of the engine’s input shaft and sends this information to the electronic control unit. The ECU uses this data to regulate the fuel injection and ignition timing.
Credit: www.justanswer.com
Toyota P0717 Input Turbine Speed Sensor
The Toyota P0717 Input Turbine Speed Sensor is located on the side of the transmission. It monitors the speed of the input shaft and sends a signal to the Engine Control Module (ECM). If the sensor detects an abnormal speed, it will set a diagnostic trouble code (DTC).
The most common cause of this DTC is a failed sensor.
How Do I Fix Code P0717
If your check engine light is on and you’re getting the code P0717, it means that your vehicle’s transmission speed sensor is malfunctioning. This can be a serious problem, as it can cause your transmission to shift erratically or not at all. Luckily, there are some things you can do to try and fix the problem yourself.
First, check the wiring harness for the transmission speed sensor. If there are any loose wires or damaged connectors, they will need to be repaired or replaced before anything else can be done. Next, clean the sensor itself with brake cleaner and a toothbrush.
Be sure to remove any dirt or debris that could be interfering with its ability to function properly. Finally, if none of these steps work, you may need to replace the transmission speed sensor entirely.
If you find yourself in need of a new transmission speed sensor, be sure to purchase one from a reputable source.
There are many cheap knock-offs out there that will not work as well as an OEM part from your trusted auto parts store. With a little patience and effort, you should be able to get your vehicle back on the road in no time!
P0717 Honda
If you’re a Honda owner, you may have seen the P0717 code pop up on your vehicle’s display. This diagnostic trouble code (DTC) is associated with the transmission input speed sensor, and it’s one of the most common codes that Honda technicians see. In this blog post, we’ll discuss what this code means, what causes it, and how to fix it.
The P0717 code is triggered when the transmission input speed sensor detects an abnormality in the rotational speed of the input shaft. This can be caused by a number of things, but most commonly it’s due to a faulty or dirty sensor, incorrect fluid level in the transmission, or a problem with the internal gears of the transmission itself.
If you see this code pop up on your vehicle’s display, it’s important to take it to a qualified technician as soon as possible.
They will be able to diagnose the cause of the problem and make any necessary repairs. Ignoring this DTC can lead to further damage to your transmission and ultimately expensive repairs down the road.
P0717 Repair Cost
P0717 Repair Cost
If your car has the P0717 code, it means that there is a problem with the transmission. This can be a costly repair, depending on the severity of the problem.
The most common cause of this code is a faulty or damaged sensor, but it can also be caused by other problems such as a loose wire or connector. If you’re not sure what’s causing the problem, it’s best to take your car to a mechanic for diagnosis.
Conclusion
If your transmission is having issues with shifting, it could be due to a problem with the input turbine speed sensor. This sensor is located on the back of the transmission, and its purpose is to send information to the computer about the speed at which the input shaft is spinning. If this sensor isn’t working properly, it can cause all sorts of shifting problems.
Fortunately, it’s not too difficult to replace this sensor yourself.
Author
-
by
-
