The 3rd generation Toyota 4Runner has a transmission fluid capacity of 6.2 quarts (5.8 liters). To change the transmission fluid, you must first remove the filler plug located on the side of the transmission case, then drain out all of the old fluid. Once drained, replace with new ATF and fill to just below the bottom edge of filler hole before reinstalling it.
Additionally, make sure to check your owner’s manual for any additional information regarding maintenance and service intervals on your vehicle.
The transmission fluid capacity of a 3rd Gen 4Runner is approximately 8.2 quarts (7.8 liters). It’s important to make sure that the proper amount of fluid is used when servicing your vehicle, as using too little or too much can lead to serious damage and may even cause your engine to fail. Regularly checking and replacing your transmission fluid should be part of any preventative maintenance program for maximum performance reliability.
Toyota 4runner Transmission Fluid Change – Drain And Fill
How Many Quarts of Transmission Fluid Does a Toyota 4Runner Take?
The Toyota 4Runner can take up to 8.2 quarts of transmission fluid, depending on the model year and type of transmission. For manual transmissions, you should use a 75W-90 gear oil; for automatic transmissions, you should use either Dexron III or Mercon V ATF. It is important to check your owner’s manual for the exact amount and type of fluid needed as it may vary from model to model.
Additionally, when replacing or refilling your transmission fluid be sure to properly dispose of any excess oil as it can be harmful if poured down drains or left in open containers.
How Much Atf Does a 3Rd Gen 4Runner Hold?
The 3rd generation 4Runner (1996-2002) has a capacity of 5.4 quarts for the automatic transmission fluid (ATF). It is important to check your owner’s manual and make sure you are using the correct type of ATF for your specific model. If you need to replace your ATF, it’s recommended that you use Genuine Toyota Type T-IV Automatic Transmission Fluid which can be found at any local auto parts store or Toyota dealership.
Additionally, it’s important to follow the service schedule outlined in your owner’s manual in order to keep your vehicle running its best and prevent any costly repairs down the road.
How Do You Change the Transfer Case Fluid on a 3Rd Gen 4Runner?
Changing the transfer case fluid on a 3rd Gen 4Runner is fairly easy and can be completed in about an hour. The first step is to locate the drain plug on the lower side of the rear differential and remove it using a ratchet and socket. Next, you’ll need to jack up your vehicle so that you can access the fill plug located at the top of your transfer case.
Once these plugs are removed, allow all of the old fluid to completely drain out before replacing with fresh fluid. Finally, re-install both plugs and check for any leaks before lowering your vehicle back onto its wheels.
What Type of Automatic Transmission is in a 3Rd Gen 4Runner?
The 3rd gen 4Runner is equipped with a four-speed electronically controlled automatic transmission. This type of transmission utilizes an electronic control unit (ECU) to monitor, adjust and optimize the shift points, gear selection, torque converter lockup and other functions of the transmission. The ECU sends signals to various components within the transmission based on engine speed, throttle position and other data inputs.
This allows for smooth shifting at all speeds and helps provide improved fuel economy over manual transmissions.
Credit: allterraintrails.com
3Rd Gen 4Runner Transmission Fluid Type
The third generation 4Runner, produced between 1996 and 2002, takes a Dexron III transmission fluid. This type of transmission fluid is a synthetic blend that provides superior lubrication and helps protect your vehicle’s internal parts from wear and tear. It also works to reduce noise while supplying the necessary protection for any components of the transmission system.
3Rd Gen 4Runner Transmission Fluid Change
Periodic maintenance is important to ensure that your 3rd gen 4Runner runs smoothly, and one of the most important tasks is changing the transmission fluid. This should be done every 60,000 miles or sooner in order to keep all internal moving parts lubricated. If you don’t change the transmission fluid regularly, it can cause damage over time leading to costly repairs.
3Rd Gen 4Runner Transmission Fluid Check
Periodic checks of the transmission fluid in your 3rd Gen 4Runner are essential for keeping it running smoothly. You should check the fluid once a month or every 5,000 miles, whichever comes first. To do this, you’ll need to locate the dipstick located near the front left side of the engine bay and remove it from its holder.
Wipe off any debris that has collected on it before reinserting it into its holder and then pull it out again to get an accurate reading of your vehicle’s transmission fluid level. Make sure that you top up with approved Toyota-specified transmission oil if necessary.
Conclusion
This blog post provided a comprehensive overview of the transmission fluid capacity of 3rd Gen 4Runner vehicles. We learned that the total transmission fluid capacity is 6.8 quarts, and it is important to refill with high-quality gear oil in order to ensure optimal performance and longevity for our vehicles. With this information, we now have a better understanding of what type of lubricant and how much should be used when maintaining our 4Runner’s transmission system.
Author
-
by
-
