How to Check Mercedes Transmission Fluid Level

To check the transmission fluid level on a Mercedes, start by parking the car and turning off the engine. Next, open the hood of your car to locate where your transmission dipstick is. Pull out the dipstick and clean it with a lint-free cloth or rag.

Insert it back into its tube before pulling it out again to check for fluid levels. The dipstick should have markings indicating “full” and “add” that will tell you if more fluid needs to be added or not. If necessary, add 1/4 -1/2 quart of automatic transmission fluid until you reach full capacity as indicated on the dipstick.

Replace the cap securely after checking and adding fluids, then close up your hood before starting your engine again.

  • Park the Mercedes on a level surface and turn off the engine
  • Make sure to leave the ignition key in position one so that all electrical components remain powered up
  • Locate the dipstick for checking transmission fluid level, which is usually located behind an access panel near the firewall at the back of your engine compartment or underneath your car by following the manufacturer’s directions provided in your owner’s manual
  • Pull out the dipstick and wipe it clean with a lint-free cloth or paper towel; make sure not to touch it with bare hands as this could contaminate it and give you inaccurate readings when reinserted into its tube
  • Push another piece of cloth, paper towel, or napkin against either side of dipstick tip to soak up any remaining oil droplets before reinserting into its tube until seated firmly without forcing it down too far beyond its regular depth as indicated on stick itself (usually about 1/4 inch)
  • 5
  • Remove dipstick again after few seconds have passed; note that if transmission fluid is low then there will only be small drops present instead of full wetness along entire length of stick – whereas high levels are shown by having more than just few drops being seen across entire surface area from top to bottom end points respectively (indicating sufficient amount has been added previously)

How to Measure Automatic transmission fluid Level Mercedes Benz E-Class. Years 2000 to 2020

How Do You Check Transmission Fluid on a Mercedes Without Dipstick?

Checking the transmission fluid on a car without a dipstick can be tricky, but it is possible. On most Mercedes models, you will need to remove an access panel located underneath the vehicle near the transmission to get to the fill plug or pan. Once you have access to these components, you should use a clean funnel and slowly add new transmission fluid through the fill plug until it begins to flow out of the drain plug at a slow rate.

This procedure allows for more precise control over how much fluid is added and ensures that none of it escapes in case of any spills during refilling. Additionally, most modern Mercedes cars are equipped with an electronic monitoring system that displays readings when checking oil levels so keep this in mind as well; however, always refer to your owner’s manual for exact instructions before attempting any work on your vehicle yourself.

Does Mercedes Have a Transmission Dipstick?

The answer to the question of whether Mercedes have a transmission dipstick is yes. All automatic transmissions on a Mercedes-Benz vehicle are equipped with a transmission dipstick or plug. This allows you to check and maintain the level of fluid in the transmission, which helps keep your car running smoothly and efficiently.

The location of the dipstick may vary depending on the model year, but typically it can be found near where the engine meets up with the transmission – usually along either side near where you’d find other important engine components such as oil filters, spark plugs, etc. The process for checking and adding fluid to your Mercedes’ transmission is similar to that of any other vehicle – simply pull out the dipstick or unscrew and remove its plug, wipe off any excess fluid from around it (this helps ensure an accurate reading), then reinsert it back into place before removing again so that you can properly read how much fluid remains in your system. It’s important not to overfill as this could lead to costly repairs down road; however if needed make sure to only use high quality fluids approved by Mercedes themselves.

How Do You Know If Your Transmission Fluid is Low on a Mercedes?

Understanding how to check your transmission fluid level is important in order to maintain the health and performance of your Mercedes. It’s a simple process that can help you avoid costly repairs down the road. To determine if your transmission fluid is low, start by parking your car on a flat surface and turning off the engine so it has time to cool down.

Then open the hood and locate the dipstick for the transmission, which should be clearly labeled. Once you’ve located it, pull out the dipstick and wipe any oil residue from it with a clean cloth or paper towel. Reinsert it all way back into its tube and remove again – this will give you an accurate reading of what level your transmission fluid is at.

If there isn’t enough fluid on the end of the stick when you pull it out (or if there are dark streaks), then this indicates that your vehicle may need more transmission fluid soon as low levels can cause damage over time due to increased heat buildup within components of gearbox system components such as clutches, seals, bearings etc..

How Do I Add Transmission Fluid to My Mercedes?

Adding transmission fluid to a Mercedes is an important part of routine maintenance. Without the right amount and type of fluid, your vehicle’s transmission can suffer from premature wear or even fail completely. To ensure that you get the job done safely and correctly, here are some steps you should take when adding transmission fluid to your Mercedes: First, make sure you know what kind of automatic or manual transmission your car has; this will determine which type of fluid you need.

Second, locate the dipstick on the side of the engine bay near the firewall – it will have “Transmission Fluid” written on it; remove it and check for any signs of contamination such as metal shavings or discoloration in order to determine if it needs to be replaced. Third, use a funnel and carefully pour new fluids into the fill tube located near where you took out the dipstick (if pouring from a bottle). Finally, insert back in its place before wiping away any spilled fluids with a clean rag.

Be sure not to overfill – only add enough so that after refilling there is still about one inch left below full line indicated by arrows on both sides of stick handle. Following these simple steps will help keep your Mercedes running smoothly!

How to Check Mercedes Transmission Fluid Level


Mercedes-Benz Transmission Fluid Dipstick Location

The transmission fluid dipstick on a Mercedes-Benz vehicle is usually located near the front of the engine, near the firewall. The exact location can vary depending on your specific model and year of manufacture, so it’s best to refer to your owner’s manual for precise instructions. It’s important to regularly check and top up your transmission fluid levels in order to keep your car running smoothly and efficiently.

Mercedes 722.9 Transmission Fluid Check

It is important to regularly check the transmission fluid in your Mercedes 722.9 vehicle, as it can be a sign of any underlying issues. If the fluid level is low or has an unusual color, this could indicate a problem and should be checked by a qualified technician as soon as possible. Checking your transmission fluid levels should become part of regular maintenance for your Mercedes 722.9 vehicle; if left unchecked, you may end up with costly repairs down the line.

Mercedes Transmission Dipstick Diy

Whether you’re a do-it-yourselfer or just need to check your transmission fluid, it’s easy to do with a Mercedes transmission dipstick. This inexpensive tool provides an accurate reading of the level and condition of your transmission fluid so that you can make sure it is at the correct level for optimal performance. Knowing how to use this simple device will help keep your vehicle running smoothly for years to come.


In conclusion, checking the transmission fluid level in a Mercedes vehicle is an important task that should not be overlooked. It can be done easily and quickly with the dipstick method or by using a scan tool to access the on-board computer. Following these simple steps will ensure your Mercedes runs smoothly for years to come, maximizing fuel efficiency and performance.


  • Alex Gearhart

    Alex Gearhart, an automotive expert specializing in transmissions, has over a decade of hands-on industry experience. With extensive knowledge in manual and automatic systems, Alex is passionate about educating car enthusiasts on vehicle maintenance. As the chief author at, Alex simplifies complex concepts for readers, helping them make informed decisions about their vehicles. Outside of work, Alex enjoys road trips, restoring classic cars, and exploring new automotive technologies.

Leave a Comment